ADG-1 Special Edition (Discontinued)
Analoger Series ADG-1 SE:
100% Analog Delay from 16ms to 1.055s of delay time with a bonus delay insert loop
This AMpT goes to 1100 milliseconds!
Features our “Guitarry Night” (Chameleon Teal) color-shifting sparkly high gloss finish and genuine solid aluminum GØRVA knobs.
The ADG-1 SE has been retired.
Please see our standard ADG-1 for current options.
The ADG-1 SE was always intended to be a limited special run. With that, the fall 2023 release was our last production run of the ADG-1 SE (although a few more were built in early 2024 with the remaining inventory) .
At this time we do not currently have plans to build this special pedal again.
Analoger Series ADG-1 SE:
100% Analog Delay from 16ms to 1.055s of delay time with a bonus delay insert loop
This AMpT goes to 1100 milliseconds!
Features our “Guitarry Night” (Chameleon Teal) color-shifting sparkly high gloss finish and genuine solid aluminum GØRVA knobs.
The ADG-1 SE has been retired.
Please see our standard ADG-1 for current options.
The ADG-1 SE was always intended to be a limited special run. With that, the fall 2023 release was our last production run of the ADG-1 SE (although a few more were built in early 2024 with the remaining inventory) .
At this time we do not currently have plans to build this special pedal again.
Analoger Series ADG-1 SE:
100% Analog Delay from 16ms to 1.055s of delay time with a bonus delay insert loop
This AMpT goes to 1100 milliseconds!
Features our “Guitarry Night” (Chameleon Teal) color-shifting sparkly high gloss finish and genuine solid aluminum GØRVA knobs.
The ADG-1 SE has been retired.
Please see our standard ADG-1 for current options.
The ADG-1 SE was always intended to be a limited special run. With that, the fall 2023 release was our last production run of the ADG-1 SE (although a few more were built in early 2024 with the remaining inventory) .
At this time we do not currently have plans to build this special pedal again.
The ADG-1 SE is a special edition of our ADG-1 analog delay. We began with a standard ADG-1 and included the following hand-made modifications and additions:
A 3rd high-voltage Xvive™ analog delay bucket has been added, allowing switching between delay times of 16ms-350ms or 50ms-1.055sec (extendable up to 1.35sec with control voltages or expression pedal)
The addition of a TRS insert on the delay loop allowing the patching of effects such as EQ or octave pedals into your delayed signal to successively affect the repeats without changing the dry tone
The addition of a center off switch to the LFO module as an upgrade from the early ADG-1 revisions
Premium “Guitarry Night” metallic shimmer sparkle finish with a high-durability gloss coating
Genuine solid aluminum GØRVA Obelisk knobs
For more information and details about the ADG-1 check out the ADG-1 page located here.
More Details
-
100% Analog signal path
Switchable true bypass or JFET-buffered bypass with switchable trails
Power: 9VDC @ <150mA (90mA Nominal, up to 350mA start up.)
Expression / CV input assignable to Time, Feedback, Mod Amount, or Mod Rate (CV range is 0-5V). Ring supplied current limited 5V.
Delay time: <50mS – 1050mS Three BBD mode, 17 - 350mS single bucket mode, 1350mS to 38mS (450-13mS) with control voltages or LFO.
Input impedance: >1MΩ
Output impedance: 1KΩ Max
Max input level: +15dBµ (4.3V RMS)
Max output level: +14dBµ (3.9V RMS)
Maximum drive: >22dB (covers attenuation to gain)
Noise Reduction 2:1 broadband with 12dB HF emphasis
-
Genuine Hammond™ die-cast aluminum enclosure
Dimensions: D=4.90” (12.5 cm), W=3.70” (9.4 cm), H=2.25” (5.8 cm)
Weight: 15.5oz (0.440kg)
The SE Goes Beyond
Increased Delay Time
Perhaps the most sought after request in the ADG-1 is added delay time. For the ADG-1 SE we added an additional delay bucket for over 1.1 seconds of total delay time with modulation. In addition to the extended delay time, the extra bucket improves delay bandwidth at longer times compared to the standard ADG-1.
As the clock time increases in an analog delay, high frequencies are naturally rolled off. On the standard ADG-1 this starts to be prominent at around 500ms and longer. In the ADG-1 SE rolloff begins to occur around 700ms. Therefore, the ADG-1 SE will have noticeably brighter repeats in the 500-700ms range than the standard ADG-1.
Delay Loop Insert
By tapping into the signal path between the delay line and the tone control, we offer a way to further alter your delay tone without affecting the dry tone. Many ideas are possible here. You can incorporate simple changes like expanded filtering or phased/flanged repeats, or you can go wild with fuzz and runaway pitch bending effects. Octave pedals are especially fun: each repeat goes increasingly up or down in octave as they are processed through the delay line again and again. Adding drive or fuzz will lead to extra intense self-oscillation effects.
Unlike many insert loops, this insert will affect the first repeat and all subsequent ones, exactly as in some of Hawker’s other famous delays. Some delay insert loops skip the first repeat.
Premium Fit & Finish
A superior product deserves a superior design. The ADG-1 SE has a premium look befitting its expanded features.
Hawker and the team deliberated over dozens of paint samples and chose an amazing color-shifting chameleon powder coat. This color shifts between blue, teal, purple, and more as the light hits it from various directions. It features a durable hard overcoat that is simply stunning to look at. And finally, we added premium solid aluminum GØRVA knobs. These eye-popping enhancements will make your ADG-1 SE the visual as well as the sonic centerpiece of your pedalboard.